Deep Color Aluminum Frame Aluminum Profile For Pergola Color
Oxidation Treatment of Aluminum Alloy:
Anodizing is a method to form a layer of oxide film on the surface
of workpiece or product by using the electrolysis principle of DC
and AC / DC, so as to increase the corrosion resistance and make
the appearance beautiful.
Electroplating treatment method is a method that takes the
workpiece as the cathode and the material forming the coating as
the anode, puts both in the tank with electroplating solution, and
then applies DC or AC / DC current to ionize the material forming
the coating, run from the electroplating solution to the workpiece
surface, and firmly adhere to it to form coatings of different
First remove the oil stain on the casting or product with
degreasing liquid, and then wash it with warm hot water at 25 to 30
degrees for thermal insulation. Then put it into the Infiltrator,
cover and seal it, vacuum to 0.7 to 0.8 PA, maintain the
temperature of about 65 ℃, and then inject the prepared Infiltrator
into the Infiltrator. After eight to ten hours of soaking, dry
compressed air shall be introduced to keep the pressure in it at
about 0.4 PA, and then for eight to ten hours. Finally, vent and
take out the castings or products for air drying.
Surface spraying method:
Spraying paint on cast aluminum parts or aluminum alloy components
and products is to improve their corrosion resistance. For castings
or products requiring good corrosion resistance, aluminum castings
or products shall be anodized or chemically oxidized before
spraying. The purpose is to increase their own corrosion resistance
and make the paint bond more firmly, and then brush the primer and
The aluminum alloy casting is put into the drum of the shot peening
machine and sprayed onto the casting surface with high-speed shot
flow. Because the casting is constantly turning at the same time,
all its surfaces are strengthened by projectile spraying.
Vacuum spraying method:
Put the product or profile to be sprayed into the vacuum chamber of
the spray plating machine as the cathode, take the material forming
the spray coating as the anode, close the vacuum chamber and vacuum
to a certain vacuum degree. Use a high-power plasma gun to sputter
the spray coating material in ionic state and deposit it on the
product or profile as the cathode to form a layer of spray coating
of 2-10 microns, Present a variety of bright luster.
|Description||Deep Color Aluminum Frame Aluminum Profile For Pergola Color
|Material Thickness(t)||t=0.8-2.0 mm|
|Materiral||Aluminum Alloy 6063|
|Color||Champagne, Silver White ,Bronze, Grey, Black, (RAL series)etc.|
|Surface Treatment||electrophoresis, anodized, wood grain, polished and etc|
|Shape||Break Bridge,T Shape,Square, Round, Flat, Oval, and according to
|Length||Normal length=6m or in customer's order|
|Usage||Building, Production Line, Decoration, Industrial, Transportation,
Door and window, etc.|
1. Pearl cotton foam for each profile;
2. Wrap with shrink film exterior;
3. Packed according to customer request.
Providing colorful products with various mechanical
performances to adapt all kinds of architectural styles
Features of Electrophoresis:
(1) High temperature water sealing.
This method utilizes the hydration reaction of aluminum oxide film
and water to turn the amorphous membrane into a hydrated
The hydration reaction can be carried out at both normal and high
temperatures, but at high temperatures, especially at the boiling
point, the hydrated crystalline membrane is a very stable and
irreversible crystalline film. Therefore, the most commonly used
aluminum oxide film is treated by boiling water or steam treatment.
(2) Sealing of inorganic salts.
Inorganic salt method can improve the fastness of organic coloring
dyes, so it is often used in chemical coloring.
(3) Organic sealing method.
This is the soaking, soaking or coating of the aluminum oxide film.
Because of the high cost and the increase of the process flow, it
is not easy to use, more or more of the two kinds of methods
mentioned above, and the first kind of high temperature hydration
is the mainstream.
|Implement National Standard||GB/5237.2-2008|
|Ingot State||Nonferrous mental industrial standard YS67-93|
|Chemical Of Oxide Film||GB/T3190-96|
|Class Of Oxide Film||AA10 , AA15 ,AA20|
|Surface Type||Matte ,Flat|
|Colors||Silver , White ,Bronze , Champagne|
|Advantage/Features||Corrosion-Resistant , Durable , Shining And Decorative|
We have several references in this industry coming from our quality
solutions, high level of finish and project management.
The automotive industry has extremely high standards when it comes
to finish. It is all about the understanding of the customer
product and customizing of the painting line to fit the product.
Controlling the line
A focal point for the automotive industry is fully control of the
finishing line and the system in general. Not only the operation of
the line, but the data collection for each product passing through
the line. It is often essential to have the exact data and
documentation of the product from the different processes of the
We deliver high quality solutions for the construction of the line,
and the technical level of the lines makes us a leading supplier
worldwide. Recipe controlling is one of many features we offer our
Please tell us the information below, and we will give the best
suggestion to you !
1. Where you intend to use the aluminium profiles?
2. If you have the estrusion drawing, send us and we develop the
3. Which color you want or tell us the architectural style you
4. Purchase quantity. It will convenient us to give you the best